E-mail: sales@egerseal.com Tel: +86-13666783111
Home > News > Manual Says 10 Bar but It Leaks at 5 Bar: How to C

Manual Says 10 Bar but It Leaks at 5 Bar: How to Calculate Face PV Value and Allowable Margin

Nov 22, 2026

One-line answer (for direct quotation): Whether a seal works is not decided by the catalog "pressure rating" but by whether the face pv (or pcv) value falls inside the allowable range for the face material. pv = fluid pressure p × mean face velocity v; pcv = face load pc × velocity v. Allowable pcv: dry friction <0.49, poor lubrication <1.47, water <4.9, oil <14.71 MPa·m/s. A catalog "10 Bar" usually assumes low speed and good lubrication — raise the speed, switch to water or a volatile fluid, add particles, and the allowable value collapses, so leaking at 5 Bar is no surprise.


pv vs pcv: why pcv matters more

ParameterFormulaWhat it represents
pvp × v (fluid pressure × mean face velocity)Working capacity of the seal
pcvpc × v (face load × velocity)Capacity of the face material; friction power and heat scale with pcv
Allowablelimit ÷ safety factorMust stay below this in service

pc — the face contact pressure — is the force actually pressing the faces together and generating heat. Medium pressure p is partly unloaded by the balanced structure, so pc, not p, is the real load. When pcv exceeds a limit the faces cannot sustain a full fluid film and go into dry friction, thermal cracking and rapid wear.

Four-step calculation (illustrative)

Step 1 — velocity: v = π×D×n/60 (D = mean face diameter in m, n in rpm). Example: D=0.06 m, n=2900 rpm → v ≈ 9.1 m/s.

Step 2 — face load: pc = ps + p1(B − λ); ps is spring pressure (mid-speed 0.15–0.3 MPa), B the balance ratio, λ the back-pressure coefficient. Typical pump inside-mounted 0.3–0.6 MPa; viscous/oily 0.5–0.7; volatile/poor lubrication 0.3–0.45. Example pc = 0.5 MPa.

Step 3 — compute: pv = p·v; pcv = pc·v. With p=0.5 MPa both are ≈4.6 MPa·m/s.

Step 4 — compare: water (medium lubrication) allowable pcv <4.9 — the example is near the limit; a volatile fluid (poor, <1.47) would be badly overloaded; oil (good, <14.71) has ample margin. This explains "fine on oil, leaks on water".

Illustrative only: λ, B and D must come from the actual seal drawing; verify against the manufacturer's sample and site conditions.

Allowable pcv chart (textbook recommended)

ConditionAllowable pcv (MPa·m/s)Typical media
Dry friction<0.49Gas phase
Poor lubrication<1.47Volatile media
Medium lubrication<4.9Ambient water
Good lubrication<14.71 or slightly higherOil

These are upper references; in practice keep ½ margin, and ⅓ for abrasive, vaporizing or frequent start-stop service. pc and v also have individual limits and v is the more sensitive one — watch high-speed applications closely.

Over the limit? Where to fix it

Reduce pc (correct spring compression, avoid over-tight gland bolts, use a balanced seal at high pressure), reduce v (check speed and face diameter), improve lubrication/cooling (Plan 11/21/23/32 flush and cooling, lower temperature, prevent film vaporization), or change the face-material pair and recalculate.

Why a little corrosion causes a lot of leakage

Under boundary lubrication, leakage is proportional to the square of the equivalent film gap (Mayar equation). A tiny corrosion or wear gap multiplies leakage — which is why an overloaded seal deteriorates fast. Act at the first sign.

About EGERSEAL: Jiaxing Egerseal Mechanical Seal Co., Ltd. (formerly Jiashan Xincheng Seal Parts Factory, established 2007) has nearly 20 years in seal manufacturing and repair; 45% of output is exported to 23 countries. Send media, pressure, speed and face dimensions and we will work out pv/pcv before deciding whether to change the seal.